Product Manuals

Touchscreen (TWE/TWP and TSB) Quick Start Guide

About Touchscreen Devices

  • There are three different model types of touchscreen devices. The TWE/TWP are touchscreen devices that are meant to be connected to the DicksonOne software application, and the TSB model is meant to be used as a standalone data logger. 
  • For the TSB model, all settings will be configured on the device itself and for the TWE/TWP models some settings will be configured through DicksonOne. 

Quick Setup

What's in the Box

Device Unit

Replaceable Sensor(s) (may look different depending on model)

AC Adapter

Ethernet Cable (for DicksonOne Units)

Additional items included

  • Kickstand – used to stand the device on a flat surface when not mounted to a wall
  • Certificate of Calibration – Document stating the device was calibrated (additional fees may apply for NIST/A2LA traceable certificates)
Start Logging Data
  1. Plug sensor(s) into the device
  2. Plug the device into power 
  3. Press the power button on the side of the device to turn it on
  4. Proceed to ‘Configure Your Device’ below to change display settings, sample interval, and more
Device Configuration

Touch the ‘Settings’ icon on the bottom right of the device screen to access the device settings screens for device configuration and device information

  1. ‘Information’ provides details about the Model, Serial Number, Firmware Version, Mac Address, Attached Sensors and Channels
  2. ‘General Settings’ allows you to configure the device’s name, time settings (format, timezone, date), sample interval for logging, units of measurement, screen saving, and brightness adjustment
  3. ‘Graph’ area allows you to choose between a graph display or text view of readings, statistics, scaling, determine what channels to display on the main screen (two max), and set min/max on/off
  4. The ‘Network’ screen will be used if your device will be registered to your DicksonOne account. After connecting your device to the internet (WiFi or Ethernet), the device will display a 6-digit registration code that is used to register the device to your account. This screen will not be used for standalone TSB loggers.
  5. ‘Alarms’ allows you to enable the alarm (up to two per channel or one high and one low per channel)
  6. ‘Calibration’ will provide details of when the sensors were calibrated, and allows you to create calibration alarms as well
  7. ‘Stored Data’ allows you to download the data from the device using USB and/or also delete the tablet data.
  8. ‘Admin Settings’ allows you to set a passcode to secure the device
Connect Device to the Internet via Ethernet (TWE/TWP Only)
  1. If you followed steps 1-3 above under “Getting Started” and the device is powered on, plug ethernet cable into the device and an active ethernet jack.
  2. A 6-­digit code will appear on the logger’s Network Settings screen under ‘Registration code’ once it has successfully connected to the internet. The code will be used to link the device to your account. See below for connecting logger to DicksonOne.
Connect Device to the Internet via WiFi (TWE/TWP Only
  1. If you followed steps 1-3 above under “Getting Started” and the device is powered on, go to the network setting screen to configure WiFi.
  2. Go to the Network Settings screen on the device and verify or switch the “Network Adapter” settings are set to WiFi
  3. Scan for your network or manually enter your SSID
  4. Input network password and configure security settings and encryption as needed. 
  5. A 6-­digit code will appear under “Registration Code” which is used to register the device to your DicksonOne account. 
Get Started with DicksonOne

Log into or create your DicksonOne account at https://www.dicksonone.com/ to get started with:

  • Device management
  • Adding users
  • Creating alarms
  • Configuring reports
    and more

Register Loggers on DicksonOne

  1. On your DicksonOne account click the ‘+Register New Hardware’
  2. Click ‘Add a DWE, TWE, or TWP’
  3. Fill out the device registration form, provide a name for the device, type in the 6-digit registration code (provided on the logger once it is connected to the internet), select a location, determine the settings, and click ‘Register Device’
  4. Data will flow into the system shortly and you will see initial data in 5-10 minutes

DicksonOne Subscription
A DicksonOne subscription is required to enable all features. Accounts may have an active subscription already and the account administrator can verify by going to DicksonOne.com > Manage > Billing.Contact your sales rep or via support (contact details provided below).

Manage Locations, Users, Alarms, Reports and more on DicksonOne

To learn how to add locations, users, configure alarms, run reports and more on DicksonOne, please visit the knowledge center by going to https://dicksondata.com/resources/support/dicksonone

Still need help?

Call 630.543.3747 today or

Scroll to Top

COVID-19: Contact our team with any questions about optimizing your Dickson products for remote work.

Submit a Ticket